![]() |
![]() |
#1 |
Admin Team
Forum Supporter Join Date: Mar 2007
Location: Lincoln, UK
Posts: 11,541
|
![]()
OK, the poll wasn't unanimous, but close enough... The few who voted "no"; your votes count as well - if this doesn't interest you please don't waste your time reading it...
I hope this may be interesting to the rest, and different to the new workshop, because this time I'm starting with bare earth, and trying to achieve something different. The purpose of this building is to house my 19hp Shanks hot bulb, and anything else I can think of - it's not going to be huge! The Shanks weighs about 3 tonnes, so (on advice) probably wants about 6 tonnes of concrete attached to it. I plan to build a 24' x 12' shed, which theoretically is big enough to get one more largish engine in. I also want the shed to be "flat floor" in case anything changes. This means that the concrete needs to be deep enough to drop some good solid resin anchors into. I'd also like to be able to use my gantry... All of these things add up to the following:
The first problem is the base - I'm no longer young and fit enough to dig the foundations and pour the concrete myself, so I've roped in some help. ![]() Using a digger, they made short work of the hole although 3 very large trailers of soil were hauled away. Into the hole has gone about 10 tonnes of hardcore, rolled and then covered with DPM. Next the hole was prepared for the concrete; ![]() Steel shuttering, and a ramp for the dumper to run in and out. The big day; ![]() Everything ready, just waiting for the first lorry to arrive. ...and the first load comes off the mixer; ![]() The dumper shifts about 3/4 metre at a time, so quite a few runs are required. Now the concrete is going in the hole - this is "industrial mix, with fibre" ![]() ![]() ![]() My friends enjoy paddling! And finally... ![]() 2 lorries and 18 tonnes of concrete later... the slab is down! 2 or 3 hours of floating after this picture was taken, and now it's quite smooth. The next step is a couple of rows of bricks, but not until the concrete has had time to harden a bit. More to follow... Martin. |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Jun 2009
Location: Bedfordshire
Posts: 4,156
|
![]()
One gets the impression that you have been so busy with the camera only your mates have done the work, or were you the foreman :-))
One thought comes to mind, when the B&BSEC put the big crossley gas engine into pitstone museum it had a hole at least three foot dug and filled with reinforcing bar and concrete and then shuttering to about a foot high with the tie down bolts sunk to at least 18 inches, and that was factory spec for the engine. Martin P
__________________
Lister optimum melius quam ceteri, quid tibi pro vita. Last edited by Lister M; 16-04-11 at 09:29 PM. |
![]() |
![]() |
![]() |
#3 |
Forum Supporter 2013
Join Date: Jun 2010
Location: Somewhere in the UK :)
Posts: 2,643
|
![]()
lets hope you wont be hit by subsidence O.o need to get the old cement mixers in for the floor of the garage, what will be fun lol
__________________
Dan |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Jun 2007
Location: Deepest Fenland
Posts: 1,605
|
![]()
I would have been tempted just to put the Shanks in the Greenhouse...
![]() Dan |
![]() |
![]() |
![]() |
#5 | |
Admin Team
Forum Supporter Join Date: Mar 2007
Location: Lincoln, UK
Posts: 11,541
|
![]() Quote:
My slab is 8" thick at the centre - it's 18" round the edge... The polyester fibre more or less removes the need for rebar. Martin. |
|
![]() |
![]() |
![]() |
#6 |
Admin Team
Forum Supporter Join Date: Mar 2007
Location: Lincoln, UK
Posts: 11,541
|
![]() |
![]() |
![]() |
![]() |
#7 |
Forum Supporter 2013
Join Date: Jan 2011
Location: Rhyl North Wales
Posts: 840
|
![]()
The greenhouse isn't going to have much light when the engine shed is built Martin... :)... you are off to a flying start, look forward to the rest of the build.
Alan.
__________________
1941 Lister D - 1939 Lister A and Stuart Generator (in progress) - 1950's BSA Field Starter - [I]all protected by electrickery, razor wire, various man traps and a rabid Yorkie... [/I] |
![]() |
![]() |
![]() |
#8 |
Admin Team
Forum Supporter Join Date: Feb 2008
Posts: 15,984
|
![]()
Serious stuff! A lot of people don't realise the volumes (and costs!) of such construction work.
Peter
__________________
Email: diesel@easynet.co.uk http://www.oldengine.org/members/diesel http://www.stationary-engine.co.uk |
![]() |
![]() |
![]() |
#9 |
Admin Team
Forum Supporter Join Date: Mar 2007
Location: Lincoln, UK
Posts: 11,541
|
![]()
A bit more progress today...
![]() The slab now has two rows of engineering bricks, which will be the base of the walls. The bricks are layed over 30 M12 stainless steel studs, which are resined into the slab. This just about completes what I can get others to do - it's pretty much down to me from now on... Once the mortar is hard, a wall plate of 4" x 2" tannalised will be layed on DPC over the studs, and bolted down. The rest of the external build will be wood. Now that the walls are in place I can also get the steelwork made - an 8" x 4" steel I-beam will run down the apex of the roof, supporting the roof and the hoist. Martin. |
![]() |
![]() |
![]() |
#10 |
Senior Member
Join Date: Nov 2008
Location: Suffolk
Posts: 221
|
![]()
No plants in the green house!! oh dear, wanna sell it ?
![]()
__________________
The bitterness of poor quality lingers long after the sweetness of low price is forgotten. |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|