UK Stationary Engine Forum
 

Go Back   UK Stationary Engine Forum > Search Forums

Showing results 1 to 25 of 500
Search took 0.08 seconds.
Search: Posts Made By: mo3mini
Forum: Ignition Systems 30-12-16, 05:54 PM
Replies: 4
Views: 1,201
Posted By mo3mini
Hi Don.. Could you post where you got this coil?...

Hi Don.. Could you post where you got this coil? As I'm sure the marvil uses the older core that I haven't been able to find for love nor money. Need one for the LZM
Forum: Ignition Systems 13-12-16, 07:18 PM
Replies: 25
Views: 3,545
Posted By mo3mini
Had a Suffolk with an open circuit cool.. It's...

Had a Suffolk with an open circuit cool.. It's ran perfectly for a good two years and then gave up the ghost. Just took a while for it to burn the gap... But I the two years only really totalled a...
Forum: General Issues 06-11-16, 09:49 PM
Replies: 7
Views: 1,364
Posted By mo3mini
I have the cast ally bed plate... Looks like I'll...

I have the cast ally bed plate... Looks like I'll be mounting it up with a little water pump :)
Forum: General Issues 06-11-16, 07:59 PM
Replies: 7
Views: 1,364
Posted By mo3mini
With a little brute force and a lot of swearing...

With a little brute force and a lot of swearing I've got the flywheel off! The first 2 inches of the flywheel is a hub.. It's screwed onto the crank shaft which isn't actually tapered.

I had to...
Forum: General Issues 06-11-16, 01:17 PM
Replies: 7
Views: 1,364
Posted By mo3mini
The flywheel in question...

The flywheel in question...
Forum: General Issues 06-11-16, 01:10 PM
Replies: 7
Views: 1,364
Posted By mo3mini
Question Villiers lZM (marine wx-11) flywheel removal?

Hi all, I recently purchased a Villiers LZM. It's a headless marine version of the WX-11... I'm stripping the engine down as the engine appears to have been underwater and the internals are nothing...
Forum: Gaskets & Seals 18-08-16, 09:40 PM
Replies: 9
Views: 4,009
Posted By mo3mini
Yep flexoid... It's oil and fuel resistant. I...

Yep flexoid... It's oil and fuel resistant. I think I used a .5 or .8mm thick.
Forum: Gaskets & Seals 18-08-16, 06:24 PM
Replies: 9
Views: 4,009
Posted By mo3mini
I made my own too... I doubt you'll ever find any...

I made my own too... I doubt you'll ever find any gaskets for the tiny Tim. Just make sure you cut all the holes in the carb gasket and it'll run like a top
Forum: Ignition, Magnetos, Plugs etc 11-07-16, 04:44 PM
Replies: 6
Views: 2,600
Posted By mo3mini
I have one from 1933 in the garage some where....

I have one from 1933 in the garage some where. It's off the Wolseley 16 in the garage, will have to dig it out and see if it works. It's a fair shade bigger than this one!

So what's in th newer...
Forum: Ignition Systems 19-06-16, 07:51 AM
Replies: 4
Views: 2,216
Posted By mo3mini
It'll have to be one of those plugs Don, doubt...

It'll have to be one of those plugs Don, doubt you'll find one over here so a ship from the states jobby... I shipped a auto lite 216 plugs for the 72. They came quicker than most stuff via Royal...
Forum: Ignition Systems 16-06-16, 05:03 PM
Replies: 4
Views: 1,492
Posted By mo3mini
In short Don that's a good reading! Nice one :)

In short Don that's a good reading! Nice one :)
Forum: General Issues 29-05-16, 08:56 AM
Replies: 2
Views: 1,102
Posted By mo3mini
Where in the bore is the piston seized? If it's...

Where in the bore is the piston seized? If it's seized at or close to top dead centre then you won't be able to pull the cylinder any further as its limited by the position of the crank... Your only...
Forum: Engine Identification 08-05-16, 06:55 PM
Replies: 27
Views: 5,579
Posted By mo3mini
Didn't Buick use this type of valve train? Which...

Didn't Buick use this type of valve train? Which rover later rebadge in the big rover p4? Looks interesting..
Forum: Restorations Section 25-04-16, 06:12 PM
Replies: 145
Views: 19,384
Posted By mo3mini
Evening Tony. Thanks again for the parts and...

Evening Tony. Thanks again for the parts and taking the time to stop on your way past to drop them off.. I have started the repairs to the exhaust expansion cover. Put a plate in and will make a...
Forum: Restorations Section 10-04-16, 07:09 PM
Replies: 5
Views: 1,301
Posted By mo3mini
Evening everyone. I've started work on the two...

Evening everyone. I've started work on the two water cooled Villiers engines. One is in better condition and requires less attention. So I've started with that engine...
...
Forum: Restorations Section 05-04-16, 05:34 PM
Replies: 5
Views: 1,301
Posted By mo3mini
Not a fan of air cooled? No problem, just convert them to water cooled!

Hi everyone, it's been a long old time since I properly posted on the forum. Mostly due to work and my dead laptop. But yesterday I collected a pair of Atco Villiers Midget mk2 engines. Normally air...
Forum: Restorations Section 18-03-16, 12:01 AM
Replies: 145
Views: 19,384
Posted By mo3mini
Hi Tony, if you could shoot me over a price for...

Hi Tony, if you could shoot me over a price for the exhaust expansion cover (with Stuart writing) and also the exhaust manifold for the top of the cylinder head that would be much aprieciated....
Forum: Generators 13-02-16, 07:51 PM
Replies: 7
Views: 1,373
Posted By mo3mini
I can get you a picture tomorrow hopefully... If...

I can get you a picture tomorrow hopefully... If the generator won't run as a motor then it's a pretty good indication that it won't charge either. From memory there are only a few wires. Have you...
Forum: General Issues 31-01-16, 03:42 PM
Replies: 2
Views: 636
Posted By mo3mini
It's a villiers F15. Late 70's I guess

It's a villiers F15. Late 70's I guess
Forum: General Issues 28-09-15, 08:14 AM
Replies: 26
Views: 2,420
Posted By mo3mini
Nearly always the problem with these solex carbs....

Nearly always the problem with these solex carbs. The one on my petter A1 was so bad that it couldn't be repaired, taken so much material away the float hieght was none existent. Glad you got it...
Forum: General Issues 27-09-15, 04:10 AM
Replies: 26
Views: 2,420
Posted By mo3mini
I have the same problem with a Briggs ZZ. On my...

I have the same problem with a Briggs ZZ. On my third carb now and still no joy. Good luck!

All I will say is that the solex carb is dreadful. I hate them.. With just two screws securing the top...
Forum: Ignition Systems 01-06-15, 07:35 AM
Replies: 6
Views: 1,651
Posted By mo3mini
Do you have a multimeter? Better still an older...

Do you have a multimeter? Better still an older analogue meter..
Forum: Ignition Systems 07-03-15, 11:59 PM
Replies: 30
Views: 7,995
Posted By mo3mini
Once your account is deleted all your videos go...

Once your account is deleted all your videos go with it.. I will happily ask makedoandmend1 if he still has a copy of the video if your interested in seeing how he got the villiers coil to fit.. He...
Forum: Ignition Systems 06-03-15, 11:01 PM
Replies: 30
Views: 7,995
Posted By mo3mini
Sorry but his account was closed a while ago.....

Sorry but his account was closed a while ago.. All the videos are gone unfortunately.

Dan
Forum: Restorations Section 15-02-15, 07:50 PM
Replies: 4
Views: 833
Posted By mo3mini
Evening all.. lovely sunny weather today so I...

Evening all.. lovely sunny weather today so I bolted the Stuart down to a bass today for its first run. I've never started one before so the carb took some getting used to, but after six or so pulls...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT +1. The time now is 01:28 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.